This kit allows large water volumes to be stored by interconecting multiple tanks together. Storage capacity is only limited by the area available for tank installation. The system uses camlok fitting for fast and secure connection.

Learn More

This orifice outlet allows captured stormwater to be released into the public drainage system once a storm event has passed. The orifice can also be configured to provide stormwater infiltaion and to prevent tank flotation in saturated ground. 48 mm is common for on-site retention systems

Learn More

This orifice outlet allows captured stormwater to be released into the public drainage system once a storm event has passed. The orifice can also be configured to provide stormwater infiltaion and to prevent tank flotation in saturated ground. 48 mm is common for on-site retention systems

Learn More

The One Water storm pit is a utility pump and pit assembly used predominately in low lying areas around the home or parcel of land you regularly use.

Learn More

This orifice outlet allows captured stormwater to be released into the public drainage system once a storm event has passed. The orifice can also be configured to provide stormwater infiltaion and to prevent tank flotation in saturated ground. 48 mm is common for on-site retention systems

Learn More

The One Water storm pit is a utility pump and pit assembly used predominately in low lying areas around the home or parcel of land you regularly use.

Learn More

This compression seal allows easy insertion of a pipe through the wall of a storage tank. Simply cut the appropriate size hole, insert the flange device and push in the pipe for a watertight seal. Learn More

Large pump 3# 4 Pin electrical connection plug IP66 for quick connect power lead.

This plug is an optional charged for fitting and Test&Tag with pump sale

Learn More

This single-pump plumbing kit (40mm or 50mm - dependent of the pump selection) is used in smaller pump stations and collection wells. The kit includes a check valve to prevent water surging back into the tank when the pump switches off and a stop valve to isolate the system for maintenance or cleaning purposes. T1 x 90° Elbow (50 mm) The only additional item required is a suitable length of 50 mm Class 9, Class 12 or Class18 PCV pressure pipe, which will vary depending of the size of the collection well. Learn More

This dual pump plumbing kit is used to connect higher specification pump combinations or other hydraulic requirements to a single manifold for pressurised outlet pipe discharge of sewer or wastewater. Each pump has a dedicated rising main configuration including a refuux valve that will stop water in the outlet pipe surging back into the tank when the pumps change operating configuration.  The configuration is designed for access to individual pumps in challenging operating situations (often necessary) including having an isolating backflow interupt ball valve allowing for maintenance of the internal configuration.  This also allow the system to continue to perform its operations as a short term but restricted measure.

Effulent level control is achieved using a series of floating switches or where smart technology is utilised a transducer level sensor provides for optional LED managed PC or remote cut-in settings and overflow alarm of response provisions. This kit includes atachment components for either approach if specified in the order.

Although fixed pedistal and discharge rising main configuration is the next level of configuration, the fresstanding pump configuration this plumbiong kit applies to, is adaptable and flexible representing value for pump station specifications and ease of on-site installation.

Learn More

Camlock fitting to allow hose connector - threaded Type C - male spigot (pump end usually)

Learn More

This kit allows large water volumes to be stored by interconecting multiple tanks together. Storage capacity is only limited by the area available for tank installation. The system uses camlok fitting for fast and secure connection.

Learn More

18 litre receiver tank for water pressure systems that connects with a 25mm BSP thread.

Learn More

The major repair to the versatile KS series submersible pump is available using a top-end assembly. The circumstance of the many pump use applications can result in inadvertent damage like crushed or torn cables or float whilst performing in the rugged environment of construction and civil works de-watering on work sites for safety and protection of assets. The KS-10 pump range is a leading product solution in the industry and being well designed for maintenance purposes for the top end of the pump through an authorised service representative. This product assembly provides a means to repair damaged conductor(s) floats and when fitted can restore the operation of the pump for normal use. This assembly product provides some certainty with continued operations having replaced power lead and float components, secured in the inlet glands with a screwed clamp on the exterior of the pump case and then allowing for renewed conductivity and earth leakage testing. Other optional repairs are also available including seal and capacitor replacement on request where a used pump is considered suitable for repair or refurbishment. Learn More

The BPS series pumps have a water resistant power lead with socket connector, held inplace with a screwed clamp on the exterior of the pump case. This lead is Type A (with no step O ring seal) and is 10 meter length with Australian three pin plug.

Learn More

The BPS series pumps have a water resistant power lead with socket connector, held inplace with a screwed clamp on the exterior of the pump case. This lead is Type A (with no step O ring seal) and is 10 meter length with Australian three pin plug.

Learn More

The major repair to the versatile KS series submersible pump is available using a top-end assembly. The circumstance of the many pump use applications can result in inadvertent damage like crushed or torn cables or float whilst performing in the rugged environment of construction and civil works de-watering on work sites for safety and protection of assets. The KS-10 pump range is a leading product solution in the industry and being well designed for maintenance purposes for the top end of the pump through an authorised service representative. This product assembly provides a means to repair damaged conductor(s) floats and when fitted can restore the operation of the pump for normal use. This assembly product provides some certainty with continued operations having replaced power lead and float components, secured in the inlet glands with a screwed clamp on the exterior of the pump case and then allowing for renewed conductivity and earth leakage testing. Other optional repairs are also available including seal and capacitor replacement on request where a used pump is considered suitable for repair or refurbishment. Learn More

The BPS series pumps have a low level inlet that allows drainage down to 3mm from floor level. This bottom grate is a thermoplastic material that has a long life span that fits into a formed recedd and securred with three stainless screws into the bottom pump chamber housing attached to the pump motor housing. A 5mm side entry grate is available as an option upon request.

Learn More

The BPS series pumps have a water resistant power lead with socket connector, held inplace with a screwed clamp on the exterior of the pump case. This lead is Type A (with no step O ring seal) and is 10 meter length with Australian three pin plug.

Learn More

The pump body housing part is a thermoplastic moulded component part of a BPS series pump(s).  As a component part it is easily replacable if damage has been caused in use and otherwise has a considerable lifespan in protected use. 

Learn More

The KS series pumps have a water resistant power lead with socket connector, held inplace with a screwed clamp on the exterior of the pump case. This lead is Type A (with no step O ring seal) and is 10 meter length with Australian three pin plug.

Learn More

The BPS series pumps have a low level inlet that allows drainage down to 3mm from floor level. This bottom grate is a thermoplastic material that has a long life span that fits into a formed recedd and securred with three stainless screws into the bottom pump chamber housing attached to the pump motor housing. A 5mm side entry grate is available as an option upon request.

Learn More

The BPS series pumps have a water resistant power lead with socket connector, held inplace with a screwed clamp on the exterior of the pump case. This lead is Type B (with new design seal) and is 10 meter length with Australian three pin plug.

Learn More