Stainless Steel hose clamps are suitable for non-pressure flexible hose connection to tail connectors for fast and secure connection. For 25mm or smaller diameter hose a single hose connector can be used. For 40mm and larger diameter hose connection it is recommended that two hose clamps be used for each hose fitting.

Camlock fitting to attach a hose connector - threaded Type C female clamped socket  (first end of hose usually)

This orifice outlet allows captured stormwater to be released into the public drainage system once a storm event has passed. The orifice can also be configured to provide stormwater infiltaion and to prevent tank flotation in saturated ground. 48 mm is common for on-site retention systems

This orifice outlet allows captured stormwater to be released into the public drainage system once a storm event has passed. The orifice can also be configured to provide stormwater infiltaion and to prevent tank flotation in saturated ground. 48 mm is common for on-site retention systems

This orifice outlet allows captured stormwater to be released into the public drainage system once a storm event has passed. The orifice can also be configured to provide stormwater infiltaion and to prevent tank flotation in saturated ground. 48 mm is common for on-site retention systems

This orifice outlet allows captured stormwater to be released into the public drainage system once a storm event has passed. The orifice can also be configured to provide stormwater infiltaion and to prevent tank flotation in saturated ground. 48 mm is common for on-site retention systems

Camlock fitting to allow hose connector - threaded Type A - female threaded socket type (pump end usually)

This orifice outlet allows captured stormwater to be released into the public drainage system once a storm event has passed. The orifice can also be configured to provide stormwater infiltaion and to prevent tank flotation in saturated ground. 48 mm is common for on-site retention systems

The BPS series pumps have a water resistant power lead with socket connector, held inplace with a screwed clamp on the exterior of the pump case. This lead is Type A (with no step O ring seal) and is 10 meter length with Australian three pin plug.

Camlock fitting to allow hose connector - threaded Type C - male spigot (pump end usually)

This dual pump plumbing kit is used to connect pump combinations to a single manifold for pressurised outlet pipe discharge of sewer or wastewater. Each pump has a dedicated rising main configuration including a refuux valve that will stop water in the outlet pipe surging back into the tank when the pumps change operating configuration.  The configuration is designed for access to individual pumps in challenging operating situations (often necessary) including having an isolating backflow interupt ball valve allowing for maintenance of the internal configuration.  This also allow the system to continue to perform its operations as a short term but restricted measure.

Effulent level control is achieved using a series of floating switches or where smart technology is utilised a transducer level sensor provides for optional LED managed PC or remote cut-in settings and overflow alarm of response provisions. This kit includes atachment components for either approach if specified in the order.

Although fixed pedistal and discharge rising main configuration is the next level of configuration, the fresstanding pump configuration this plumbiong kit applies to, is adaptable and flexible representing value for pump station specifications and ease of on-site installation.

This hose kit assembly is normally connected to a submersible pump outlet fitted with a type F camlock connector.  The hose kit assembly with male and female combination camlock connectors allows multiple extension hose kits for unlimited drainage hoses to control the wastewater over a longer distance to the safe discharge point.

The assembly hose kit uses medium density PVC layflat hose with quality camlock fitting clamped to the hose for fast and secure connection. 

This kit allows large water volumes to be stored by interconecting multiple tanks together. Storage capacity is only limited by the area available for tank installation. The system uses camlok fitting for fast and secure connection.

This kit allows large water volumes to be stored by interconecting multiple tanks together. Storage capacity is only limited by the area available for tank installation. The system uses camlok fitting for fast and secure connection.

The selection of a pedestal discharge pipe configuration and pump access rail system are used in industrial applications that provide a system of operating risk reduction and ease of maintenance for the operations of the pump installation.

This orifice outlet allows captured stormwater to be released into the public drainage system once a storm event has passed. The orifice can also be configured to provide stormwater infiltaion and to prevent tank flotation in saturated ground. 48 mm is common for on-site retention systems

This orifice outlet allows captured stormwater to be released into the public drainage system once a storm event has passed. The orifice can also be configured to provide stormwater infiltaion and to prevent tank flotation in saturated ground. 48 mm is common for on-site retention systems

Minsup type A claw fitting with 25mm threaded socket connector.

This is European type connector with open claw channel that will typically match with 19mm and 25mm hose connectors.

This kit allows large water volumes to be stored by interconecting multiple tanks together. Storage capacity is only limited by the area available for tank installation. The system uses camlok fitting for fast and secure connection.

This kit allows large water volumes to be stored by interconecting multiple tanks together. Storage capacity is only limited by the area available for tank installation. The system uses camlok fitting for fast and secure connection.

The BPS series pumps have a water resistant power lead with socket connector, held inplace with a screwed clamp on the exterior of the pump case. This lead is Type A (with no step O ring seal) and is 10 meter length with Australian three pin plug.